hp.com home products and services support and drivers solutions how to buy
cd-rom home
End of Jump to page title
HP OpenVMS systems
documentation

Jump to content


HP TCP/IP Services for OpenVMS

HP TCP/IP Services for OpenVMS
Tuning and Troubleshooting


Previous Contents Index

2.1.5 Modifying Socket Subsystem Attributes

The socket subsystem attributes control the maximum number of pending connection attempts per server socket (that is, the maximum depth of the listen or SYN queue) and other behavior. You may be able to improve server performance by modifying the socket subsystem attributes described in Table 2-2.

Table 2-2 socket Subsystem Attributes
Attribute Description
somaxconn Controls the maximum number of pending TCP connections.
sominconn Controls the minimum number of pending TCP connections.
sb_max Controls the maximum size of a socket buffer.

In addition, the socket subsystem attributes sobacklog_hiwat , sobacklog_drops , and somaxconn_drops track events related to socket listen queues. By monitoring these attributes, you can determine whether the queues are overflowing.

2.1.5.1 Increasing the Maximum Number of Pending TCP Connections

The socket subsystem attribute somaxconn specifies the maximum number of pending TCP connections (the socket listen queue limit) for each server socket (for example, for the HTTP server socket). Busy servers often experience large numbers of pending connections. If the listen queue connection limit is too small, incoming connection requests may be dropped. Pending TCP connections can be caused by lost packets in the internet or denial of service (DOS) attacks.

The default value for somaxconn is 1024.

HP recommends increasing the somaxconn attribute to the maximum value, except on low-memory systems. The maximum value is 65535. Specifying a value that is higher than the maximum value can cause unpredictable behavior.

2.1.5.2 Increasing the Minimum Number of Pending TCP Connections

The socket subsystem attribute sominconn specifies the minimum number of pending TCP connections (backlog) for each server socket. This attribute controls how many SYN packets can be handled simultaneously before additional requests are discarded. Network performance can degrade if a client saturates a socket listen queue with erroneous TCP SYN packets, effectively blocking other users from the queue.

The value of the sominconn attribute overrides the application-specific backlog value, which may be set too low for some server software. If you do not have your application source code, you can use the sominconn attribute to set a sufficient pending-connection quota.

The default value is 0.

HP recommends increasing the value of the sominconn attribute to the maximum value of 65535. The value of the sominconn attribute should be the same as the value of the somaxconn attribute (see Section 2.1.5.1).

2.1.5.3 Increasing the Maximum Size of a Socket Buffer

The socket subsystem attribute sb_max specifies the maximum size of a socket buffer.

Performance Benefits and Tradeoffs

Increasing the maximum size of a socket buffer may improve performance if your applications can benefit from a large buffer size.

You can modify the sb_max attribute without rebooting the system.

When to Tune

If you require a large socket buffer, increase the maximum socket buffer size.

Recommended Values

The default value of the sb_max attribute is 128 KB. Increase this value before you increase the size of the transmit and receive socket buffers.

2.1.6 Modifying Internet Subsystem Attributes

You may be able to improve inet subsystem performance by modifying the attributes described in Table 2-3.

Table 2-3 inet Subsystem Attributes
Attribute Description
tcbhashsize Controls the size of a TCP hash table.
tcbhashnum Specifies the number of TCP hash tables.
inifaddr_hsize Controls the size of the kernel interface alias table.
tcp_keepinit Specifies the TCP partial connection timeout rate.
tcp_rexmit_interval_min Specifies the rate of TCP retransmissions.
tcp_keepalive_default Enables or disables the TCP keepalive function.
tcp_msl Specifies the TCP connection context timeout rate.
tcp_nodelack Delays acknowledgment messages after the receipt of network frames.
ipport_userreserved Specifies the maximum value for the range of outgoing connection ports.
ipport_userreserved_min Specifies the minimum value for the range of outgoing connection ports.
pmtu_enabled Enables or disables use of the PMTU protocol.
ipqmaxlen Prevents dropped input packets.

2.1.6.1 Increasing the Size of a TCP Hash Table

You can modify the size of the hash table that the kernel uses to look up Transmission Control Protocol (TCP) control blocks. The inet subsystem attribute tcbhashsize specifies the number of hash buckets in the kernel TCP connection table (the number of buckets in the inpcb hash table).

Performance Benefits and Tradeoffs

The kernel must look up the connection block for every TCP packet it receives, so increasing the size of the table can speed the search and improve performance. This results in a small increase in pooled memory.

You can modify the tcbhashsize attribute without rebooting the system.

When to Tune

Increase the number of hash buckets in the kernel TCP connection table if you have an Internet server.

Recommended Values

The default value of the tcbhashsize attribute is 512. For Internet servers, set the tcbhashsize attribute to 16384.

2.1.6.2 Increasing the Number of TCP Hash Tables

You can increase the number of hash tables the kernel uses to look up TCP control blocks. Because the kernel must look up the connection block for every Transmission Control Protocol (TCP) packet it receives, a bottleneck may occur at the TCP hash table in SMP systems. Increasing the number of tables distributes the load and may improve performance. The inet subsystem attribute tcbhashnum specifies the number of TCP hash tables.

Performance Benefits and Tradeoffs

For SMP systems, you may be able to reduce hash table lock contention by increasing the number of hash tables that the kernel uses to look up TCP control blocks. This will slightly increase pooled memory.

You cannot modify the tcbhashnum attribute without rebooting the system.

When to Tune

Increase the number of TCP hash tables if you have an SMP system that is an Internet server.

Recommended Values

The minimum value of the tcbhashnum attribute is 1 (the default). The maximum value is 64. For busy server SMP systems, you can increase the value of the tcbhashnum attribute to 16. If you increase this attribute, you should also increase the size of the hash table by a similar factor. See Section 2.1.6.1 for more information.

2.1.6.3 Increasing the Size of the Kernel Interface Alias Table

The inet subsystem attribute inifaddr_hsize specifies the number of hash buckets in the kernel interface alias table ( in_ifaddr ).

If a system is used as a server for many different server domain names, each of which is bound to a unique IP address, the code that matches arriving packets to the right server address uses the hash table to speed lookup operations for the IP addresses.

Performance Benefits and Tradeoffs

Increasing the number of hash buckets in the table can improve performance on systems that use large numbers of aliases.

When to Tune

Increase the number of hash buckets in the kernel interface alias table if your system uses large numbers of aliases.

You can modify the inifaddr_hsize attribute without rebooting the system.

Recommended Values

The default value of the inet subsystem attribute inifaddr_hsize is 32; the maximum value is 512.

For the best performance, the value of the inifaddr_hsize attribute is always rounded down to the nearest power of 2. If you are using more than 500 interface IP aliases, specify the maximum value of 512. If you are using fewer than 250 aliases, use the default value of 32. For a number of aliases between 250 and 500, use a value that is a power of 2 between 32 and 512.

2.1.6.4 Increasing the TCP Partial Connection Timeout Rate

If increasing the somaxconn limit does not prevent the listen queue from filling, or if the default grows to an excessive length, you can make partial connections time out sooner by decreasing the value of the inet subsystem attribute tcp_keepinit .

The tcp_keepinit attribute specifies the amount of time that a partial connection remains on the socket listen queue before it times out. Partial connections consume socket listen queue slots and fill the queue with connections in the SYN_RCVD state.

Performance Benefits and Tradeoffs

Network performance can degrade if a client overfills a socket listen queue with TCP SYN packets, thereby blocking other users from the queue. To eliminate this problem, increase the value of the sominconn attribute to its maximum value. If the system continues to drop SYN packets, decrease the value of the tcp_keepinit attribute to 30 (15 seconds). Monitor the values of the sobacklog_drops and somaxconn_drops attributes to determine whether the system is dropping packets. (See Section 2.1.7 for more information about event counters.)

You can modify the tcp_keepinit attribute without rebooting the system.

When to Tune

Modify the TCP partial-connection timeout limit if the value of the somaxconn_drops attribute increases often. If this occurs, decrease the value of the tcp_keepinit attribute.

Recommended Values

The value of the tcp_keepinit attribute is in units of 0.5 seconds. The default value is 150 units (75 seconds). If the value of the sominconn attribute is 65535, use the default value of the tcp_keepinit attribute.

If you set the value of the tcp_keepinit attribute too low, you may prematurely break connections associated with clients on network paths that are slow or network paths that lose many packets. Do not set the value to less than 20 units (10 seconds).

2.1.6.5 Slowing TCP Retransmission Rate

The inet subsystem attribute tcp_rexmit_interval_min specifies the minimum amount of time before the first TCP retransmission.

Performance Benefits and Tradeoffs

You can increase the value of the tcp_rexmit_interval_min attribute to slow the rate of TCP retransmissions, which decreases congestion and improves performance.

You can modify the tcp_rexmit_interval_min attribute without rebooting the system.

When to Tune

Not every connection needs a long retransmission time. Usually, the default value is adequate. However, for some wide area networks (WANs), the default retransmission interval may be too small, causing premature retransmission timeouts. This may lead to duplicate transmission of packets and the erroneous invocation of the TCP congestion-control algorithms.

To check for retransmissions, use the netstat -p tcp command and examine the output for data packets retransmitted.

Recommended Values

The tcp_rexmit_interval_min attribute is specified in units of 0.5 second. The default value is 2 units (1 second).

Do not specify a value that is less than 1 unit. Do not change the attribute unless you fully understand TCP algorithms and your network topology.

2.1.6.6 Enabling the TCP Keepalive Function

The keepalive function enables the periodic transmission of messages on a connected socket in order to keep connections active. Sockets that do not exit cleanly are cleaned up when the keepalive interval expires. If keepalive is not enabled, those sockets continue to exist until you reboot the system.

Applications enable keepalive for sockets by setting the setsockopt function's SO_KEEPALIVE option. To override programs that do not set keepalive , or if you do not have access to the application sources, use the inet subsystem attribute tcp_keepalive_default to enable keepalive functionality.

Performance Benefit

Keepalive functionality cleans up sockets that do not exit cleanly when the keepalive interval expires.

You can modify the tcp_keepalive_default attribute without rebooting the system. However, sockets that already exist will continue to use old behavior, until the applications are restarted.

When to Tune

Enable keepalive if you require this functionality, and you do not have access to the source code.

Recommended Values

To override programs that do not set keepalive, or if you do not have access to application source code, set the inet subsystem attribute tcp_keepalive_default to 1 in order to enable keepalive for all sockets.

If you enable keepalive, you can also configure the TCP options listed in Table 2-4 for each socket.

Table 2-4 TCP Keepalive Options
Option Description
tcp_keepidle Specifies the amount of idle time, in seconds, before sending a keepalive probe. The default interval is two hours.
tcp_keepintvl Specifies the amount of time, in seconds, between retransmission of keepalive probes. The default interval is 75 seconds.
tcp_keepcnt Specifies the maximum number of keepalive probes that are sent before the connection is dropped. The default is 8 probes.
tcp_keepinit Specifies the maximum amount of time, in seconds, before an initial connection attempt times out. The default is 75 seconds.

2.1.6.7 Increasing the Timeout Rate for TCP Connection Context

The TCP protocol includes a concept known as the Maximum Segment Lifetime (MSL). When a TCP connection enters the TIME_WAIT state, it must remain in this state for twice the value of the MSL; otherwise, undetected data errors on future connections can occur. The inet subsystem attribute tcp_msl determines the maximum lifetime of a TCP segment and the timeout value for the TIME_WAIT state.

In some situations, the default timeout value for the TIME_WAIT state (60 seconds) is too large, thereby reducing the value of the tcp_msl attribute frees connection resources sooner than the default setting.

Performance Benefits and Tradeoffs

You can decrease the value of the tcp_msl attribute to make the TCP connection context time out more quickly at the end of a connection. However, this will increase the chance of data corruption.

You can modify the tcp_msl attribute without rebooting the system.

When to Tune

Usually, you do not have to modify the timeout limit for the TCP connection context.

Recommended Values

The value of the tcp_msl attribute is set in units of 0.5 second. The default value is 60 units (30 seconds), which means that the TCP connection remains in TIME_WAIT state for 60 seconds, or twice the value of the MSL.

Do not reduce the value of the tcp_msl attribute unless you fully understand the design and behavior of your network and the TCP protocol. It is strongly recommended that you use the default value; otherwise, there is the potential for data corruption.

2.1.6.8 Disabling Delayed Acknowledgment

The TCP/IP software can send an acknowledgment packet for every frame received over the network. However, this is an inefficient mode of operation. The tcp_nodelack attribute controls the delay of acknowledgment messages.

When this attribute is set to 0 (the default), network traffic is greatly reduced. If you set this attribute to 1, an acknowledgment message is sent for every frame received, increasing network traffic and impacting the performance of the network server.

2.1.6.9 Modifying the Range of Outgoing Connection Ports

When a TCP or UDP application creates an outgoing connection, the kernel dynamically allocates a nonreserved port number for each connection. The kernel selects the port number from a range of values between the value of the inet subsystem attribute ipport_userreserved_min and the value of the ipport_userreserved attribute. Using the default values for these attributes, the range of outgoing ports starts at 49152 and stops at 65535.

Performance Benefits and Tradeoffs

Modifying the range of outgoing connections provides TCP and UDP applications with a specific range of ports.

You can modify the ipport_userreserved_min and ipport_userreserved attributes without rebooting the system.

When to Tune

If your system requires outgoing ports from a particular range, you can modify the values of the ipport_userreserved_min and ipport_userreserved attributes.

Recommended Values

The default value of the ipport_userreserved_min attribute is 49152. The default value of the ipport_userreserved is 65535. The maximum value of each attribute is 65535.

Do not reduce the ipport_userreserved attribute to a value that is less than 65535, and do not reduce the ipport_userreserved_min attribute to a value that is less than 49152.

2.1.6.10 Disabling Use of the PMTU Protocol

Packets transmitted between servers are fragmented into units of a specific size in order to ease transmission of the data over routers and small-packet networks, such as Ethernet networks. When the inet subsystem attribute pmtu_enabled is enabled (set to 1, which is the default behavior), the system determines the largest common path maximum transmission unit (PMTU) value between servers and uses it as the unit size. The system also creates a routing table entry for each client network that attempts to connect to the server.

Performance Benefits and Tradeoffs

If a server handles traffic among many remote clients, disabling the use of a PMTU can decrease the size of the kernel routing table, which improves server efficiency. However, on a server that handles local traffic and some remote traffic, disabling the use of a PMTU can degrade bandwidth.

When to Tune

If an Internet server has poor performance and the routing table increases to more than 1000 entries, you should disable the use of PMTU. This is also recommended if you have a server that handles traffic among many remote clients.

Recommended Values

To disable the use of PMTU protocol, set the value of the pmtu_enabled attribute to 0.


Previous Next Contents Index